Nowadays there is a big effort toward improving the low-pressure turbine efficiency even to the extent of penalizing other relevant design parameters. LP turbine efficiency influences SFC more than other modules in the engine. Most of the research has been oriented to reduce profile losses, modifying the suction surface, the pressure surface, or the three-dimensional regions of the flow. To date, the pressure surface has received very little attention. The dependence of the profile losses on the behavior of both pressure and suction surfaces has been investigated for the case of a high-lift design that is representative of a modern civil engine LP turbine. The experimental work described in this paper consists of two different sets of experiments: the first one concluded an improved pressure surface definition, and the second set was oriented to achieve further improvement in losses modifying the profile suction surface. Three profiles were designed and tested over a range of conditions. The first profile is a thin-solid design. This profile has a large pressure side separation bubble extending from near the leading edge to midchord. The second profile is a hollow design with the same suction surface as the first one, but avoiding pressure surface separation. The third one is also a hollow design with the same pressure surface as the second profile, but more aft loaded suction surface. The study is part of a wider ongoing research program covering the effects of the different design parameters on losses. The paper describes the experiments conducted in a low-speed linear cascade facility. It gathers together steady and unsteady loss measurements by wake traverse and surface pressure distributions for all the profiles. It is shown that thick profiles generate only around 90 percent of the losses of a thin-solid profile with the same suction surface. The results support the idea of an optimum axial position for the peak Mach number. Caution is recommended, as profile aft loading would not be a completely secure method for reducing losses.

Curtis, E. M., Hodson, H. P., Banieghbal, M. R., Howell, R. J., and Harvey, N. W., 1997, “Development of Blade Profiles for Low Pressure Turbine Applications,” ASME J. Turbomach., 119, July.
Howell, R. J., Ramesh, O. N., Hodson, H. P., Harvey, N. W., and Schulte, V., 2000, “High Lift and Aft Loaded Profiles for Low Pressure Turbines,” ASME Paper No 2000-GT-0261, ASME Turbo Expo 2000, Munich, May.
Cobley, K., Coleman, N., Siden, G., and Arndt, N., 1997, “Design of New Three Stage Low Pressure Turbine for the BMW Rolls-Royce BR715 Turbofan Engine,” ASME Paper No. 97-GT-419, Orlando, FL, June.
Denton, J. D. 1999, “State of the Art and Future of Turbine Technology,” Proc. International Gas Turbine Congress, Kobe. pp. 27–37.
Engber, M., and Fottner, L., 1995, “The Effect of Incoming Wakes in Boundary Later Transition of a Highly Loaded Turbine Cascade,” Paper No. 21, AGARD Conference. Loss Mechanisms and Unsteady Flows in Turbomachinery, Derby, May.
, and
, “
Two Dimensional Transonic Aerodynamic Design Method
, No
, pp.
Harvey, N. W., Schulte, V., Howell, R. J., and Hodson, H. P., 1999, “The Role of Research in the Aerodynamic Design of an Advanced Low Pressure Turbine,” 3rd European Conf. on Turbomachinery, IMechE, London, Mar.
Howell, R. J., 1999, “Wake-Separation Bubble Interactions in Low Reynolds Number Turbomachinery,” Ph.D. dissertation, Cambridge University, Cambridge, UK.
Schulte, V., and Hodson, H. P., 1998, “Unsteady Wake-Induced Boundary Layer Transition in High Lift LP Turbines,” ASME J. Turbomach., 120, Jan.
Ulizar, I., and Gonza´lez, P., “Aerodynamic Design of a New Five Stage Low Pressure Turbine for the Rolls Royce Trent 500 Turbofan,” accepted for publ., ASME J. Turbomach.
Banieghbal, M. R., Curtis, E. M., Denton, J. D., Hodson, H. P., Huntsman, J., and Schulte, V., 1995, “Wake Passing in LP Turbines,” Paper No. 23, AGARD Conference. Loss Mechanisms and Unsteady Flows in Turbomachinery, Derby, May.
Hatman, A., and Wang, T., 1998, “A Prediction Model for Separated-Flow Transition,” ASME Paper No. 98-GT-237, Stockholm, June.
You do not currently have access to this content.