Abstract
In this work, we research a reciprocating hybrid linear guideway and study its load capacity. This hybrid guideway's bearing surface is designed with an annular groove and two sloped shallow recesses. The analysis is based on modeling by mass-conserving cavitation algorithm (p − θ cavitation algorithm), where a modified smoothing switch function is raised for better convergence. Focusing on the normal direction to reciprocation, the load-guideway system is simplified as a single-degree-of-freedom linear time-varying system and solved by Newmark-β method. Due to the hybrid guideway's time-varying dynamic characteristics, there is a normal vibration in reciprocation. By analyzing two typical load cases in detail, the results indicate that the hybrid guideway has greater load capacity than the hydrostatic guideway, and the normal vibration is small enough for most engineering situations.
Issue Section:
Hydrodynamic Lubrication
Keywords:
hybrid guideway,
cavitation,
load capacity,
normal vibration,
films,
hydrodynamic lubrication,
hydrostatic lubrication,
sliding
Topics:
Algorithms,
Cavitation,
Hydrostatics,
Reciprocating motion,
Stress,
Vibration,
Modeling,
Switches,
Pressure
References
1.
Sharma
, S. C.
, Jain
, S. C.
, and Bharuka
, D. K.
, 2002
, “Influence of Recess Shape on the Performance of a Capillary Compensated Circular Thrust pad Hydrostatic Bearing
,” Tribol. Int.
, 35
(6
), pp. 347
–356
. 10.1016/S0301-679X(02)00013-02.
Bouzidane
, A.
, and Thomas
, M.
, 2007
, “Equivalent Stiffness and Damping Investigation of a Hydrostatic Journal Bearing
,” Tribol. Trans.
, 50
(2
), pp. 257
–267
. 10.1080/104020007013097453.
Rowe
, W. B.
, 2012
, Hydrostatic, Aerostatic and Hybrid Bearing Design
, Butterworth-Heinemann
, Oxford
.4.
Kumar
, V.
, Sharma
, S. C.
, and Jain
, S. C.
, 2006
, “On the Restrictor Design Parameter of Hybrid Journal Bearing for Optimum Rotordynamic Coefficients
,” Tribol. Int.
, 39
(4
), pp. 356
–368
. 10.1016/j.triboint.2005.03.0155.
Wang
, L.
, Pei
, S.
, Xiong
, X.
, and Xu
, H.
, 2014
, “Study on the Static Performance and Stability of a Water-Lubricated Hybrid Bearing With Circumferential Grooves and Stepped Recesses Considering the Influence of Recess Sizes
,” Tribol. Trans.
, 57
(1
), pp. 36
–45
. 10.1080/10402004.2013.8404076.
Awasthi
, R. K.
, Jain
, S. C.
, and Sharma
, S. C.
, 2006
, “Finite Element Analysis of Orifice-Compensated Multiple Hole-Entry Worn Hybrid Journal Bearing
,” Finite Elem. Anal. Des.
, 42
(14
), pp. 1291
–1303
. 10.1016/j.finel.2006.06.0077.
Dwivedi
, V. K.
, Chand
, S.
, and Pandey
, K. N.
, 2013
, “Effect of Number and Size of Recess on the Performance of Hybrid (Hydrostatic/Hydrodynamic) Journal Bearing
,” Procedia Eng.
, 51
, pp. 810
–817
. 10.1016/j.proeng.2013.01.1168.
Fesanghary
, M.
, and Khonsari
, M. M.
, 2012
, “Topological and Shape Optimization of Thrust Bearings for Enhanced Load-Carrying Capacity
,” Tribol. Int.
, 53
, pp. 12
–21
. 10.1016/j.triboint.2012.03.0189.
Chen
, L.
, Li
, R.
, Xie
, F.
, and Wang
, Y.
, 2019
, “Load-Bearing Capacity Research in Wet Clutches With Surface Texture
,” Measurement
, 142
, pp. 96
–104
. 10.1016/j.measurement.2019.04.05510.
Ivantysynova
, M.
, and Lasaar
, R.
, 2004
, “An Investigation Into Micro- and Macrogeometric Design of Piston/Cylinder Assembly of Swash Plate Machines
,” Int. J. Fluid Power
, 5
(1
), pp. 23
–36
. 10.1080/14399776.2004.1078118111.
Garrett
, R.
, 2009
, Investigation of Reducing Energy Dissipation in Axial Piston Machines of Swashplate Type Using Axially Waved Pistons
, Purdue University
, West Lafayette, IN
.12.
Murrenhoff
, H.
, Eneke
, C.
, Gels
, S.
, Heipl
, O.
, Leonhard
, L.
, Schumacher
, J.
, and Wohlers
, A.
, 2010
, “Efficiency Improvement of Fluid Power Components Focusing on Tribological Systems
,” Seventh International Fluid Power Conference
, Aachen, Germany
, Mar. 22–24
.13.
Gropper
, D.
, Wang
, L.
, and Harvey
, T. J.
, 2016
, “Hydrodynamic Lubrication of Textured Surfaces: A Review of Modeling Techniques and key Findings
,” Tribol. Int.
, 94
, pp. 509
–529
. 10.1016/j.triboint.2015.10.00914.
Elrod
, H. G.
, 1975
, “A Computer Program for Cavitation and Starvation Problems
,” Proceedings of the 1st Leeds-Lyon Symposium on Tribology
, Cavitation and Related Phenomena in Lubrication, 37.15.
Jakobsson
, B.
, and Floberg
, L.
, 1958
, “The Finite Journal Bearing Considering Vaporization
,” Wear
, 2
(2
), p. 158
.16.
Olsson
, K.
, 1965
, “Cavitation in dynamically loaded bearings,” Transactions of Chalmers University of Technologies, 308.17.
Wijnant
, Y. H.
, and Venner
, C. H.
, 1999
, “Contact Dynamics in Starved Elastohydrodynamic Lubrication,” Tribology Series
, D.
Dowson
, M.
Priest
, C. M.
Taylor
, P.
Ehret
, T. H. C.
Childs
, G.
Dalmaz
, Y.
Berthier
, L.
Flamand
, J. M.
Georges
, and A. A.
Lubrecht
, eds., Elsevier
, New York
, pp. 705
–716
.18.
Ausas
, R.
, Ragot
, P.
, Leiva
, J.
, Jai
, M.
, Bayada
, G.
, and Buscaglia
, G. C.
, 2007
, “The Impact of the Cavitation Model in the Analysis of Microtextured Lubricated Journal Bearings
,” ASME J. Tribol.
, 129
(4
), pp. 868
–875
. 10.1115/1.276808819.
Ausas
, R. F.
, Jai
, M.
, and Buscaglia
, G. C.
, 2009
, “A Mass-Conserving Algorithm for Dynamical Lubrication Problems With Cavitation
,” ASME J. Tribol.
, 131
(3
), p. 031702
. 10.1115/1.314290320.
Qiu
, Y.
, and Khonsari
, M. M.
, 2009
, “On the Prediction of Cavitation in Dimples Using a Mass-Conservative Algorithm
,” ASME J. Tribol.
, 131
(4
), p. 041702
. 10.1115/1.317699421.
Buscaglia
, G. C.
, El Alaoui Talibi
, M.
, and Jai
, M.
, 2015
, “Mass-conserving Cavitation Model for Dynamical Lubrication Problems. Part I: Mathematical Analysis
,” Math. Comput. Simul.
, 118
, pp. 130
–145
. 10.1016/j.matcom.2014.11.02622.
Pei
, S.
, Xu
, H.
, Yun
, M.
, Shi
, F.
, and Hong
, J.
, 2016
, “Effects of Surface Texture on the Lubrication Performance of the Floating Ring Bearing
,” Tribol. Int.
, 102
, pp. 143
–153
. 10.1016/j.triboint.2016.05.01423.
Rosenkranz
, A.
, Costa
, H. L.
, Profito
, F.
, Gachot
, C.
, Medina
, S.
, and Dini
, D.
, 2019
, “Influence of Surface Texturing on Hydrodynamic Friction in Plane Converging Bearings—An Experimental and Numerical Approach
,” Tribol. Int.
, 134
, pp. 190
–204
. 10.1016/j.triboint.2019.01.04224.
Fesanghary
, M.
, and Khonsari
, M. M.
, 2011
, “A Modification of the Switch Function in the Elrod Cavitation Algorithm
,” ASME J. Tribol.
, 133
(2
), p. 024501
. 10.1115/1.400348425.
Nitzschke
, S.
, Woschke
, E.
, Schmicker
, D.
, and Strackeljan
, J.
, 2016
, “Regularised Cavitation Algorithm for use in Transient Rotordynamic Analysis
,” Int. J. Mech. Sci.
, 113
, pp. 175
–183
. 10.1016/j.ijmecsci.2016.04.02126.
Venner
, C.
, and Lubrecht
, T.
, 2000
, Multilevel Methods in Lubrication.27.
Wang
, X.
, Li
, H.
, Li
, M.
, Bai
, H.
, and Meng
, G.
, 2015
, “Dynamic Characteristics of Magnetorheological Fluid Lubricated Journal Bearing and Its Application to Rotor Vibration Control
,” J. VibroEng.
, 17
(4
), pp. 1912
–1928
.Copyright © 2020 by ASME
You do not currently have access to this content.
