... by multistage fuzzy comprehensive assessment method (MFCA), and the risk of pipeline is also obtained by risk matrix, the risk assessment flow is shown in Fig. 1 . This paper is first presented in ASME PVP2008. risk analysis buried pipeline fuzzy theory design engineering erosion fault...

... ASME Section III Subsection NH. 6 ASME Section II Part D Table 2A. 7 ASME B31.3. 07 06 2010 26 09 2011 16 02 2012 16 02 2012 design engineering metals occupational safety pipes power plants standards thermal stress cracking welding piping fatigue...

... or Equal to 454 °C (850 °F) Section VIII, Division 22,” American Society of Mechanical Engineers. 01 05 2009 07 12 2010 19 01 2012 19 01 2012 alloys creep design engineering fatigue testing internal stresses pressure vessels tensile strength A number of alloys...

... is independent of coordinates, is the only degree of freedom. The SDoF response of the spherical shell is the so-called breathing mode response. 31 01 2011 21 09 2011 13 01 2012 13 01 2012 design engineering explosions explosives impact (mechanical) pressure vessels shapes...

... modes Frequency of the in-plane modes of the U-tube for different support conditions (12.7 mm tube) bars boilers design engineering dynamic response elasticity flow instability flow measurement heat transfer mechanical testing numerical analysis pipe flow pipes turbulence...

... 2011 19 10 2011 19 10 2011 automatic optical inspection crack detection design engineering finite element analysis gradient methods nuclear power stations thermal stress cracking thickness measurement walls thermal fatigue thermal stress crack propagation crack network...

... 2010 18 02 2011 13 10 2011 13 10 2011 containers convection cooling design engineering emissivity radioactive waste repositories thermal analysis thermal conductivity vitrification The Belgian National Agency for Radioactive Waste and Enriched Fissile Material...

... design engineering fatigue temperature A number of alloys have applications slightly into the creep range that are in cyclic service, such as process reactors. The 2007 edition of Section VIII, Division 2 ( 1 ) provides allowable stresses for these materials, which may be controlled by creep...

... thickness. Using the same technique, Jahed and Bidabadi analyzed the first and second stages of creep in an axisymmetric body, such as a rotating disk and pressure vessels ( 9 ). 24 04 2010 02 01 2011 14 07 2011 14 07 2011 blades creep design engineering discs (structures...

... assumptions made in the elastic analysis are valid for this configuration. 01 10 2010 08 02 2011 09 05 2011 09 05 2011 design engineering elastoplasticity heat exchangers pipes plastic deformation stress analysis work hardening Conventional tube sheet design...

... . 18 03 2010 09 01 2011 09 05 2011 09 05 2011 deformation design engineering finite element analysis pipes power plants sensing device design pipe deformation accuracy stability experimental setup numerical simulation High temperature pressurized pipes...

... for Evaluating the Remaining Strength of Corroded Pipe ,” American Gas Association Report No. PR 3-805. 23 07 2009 17 08 2010 06 04 2011 06 04 2011 corrosion decision making design engineering life cycle costing maintenance engineering Monte Carlo methods pipelines...

... for the header under combined piping loads. aluminium bending brazing design engineering elasticity finite element analysis heat exchangers mechanical strength pipes plasticity plates (structures) torque individual limit load nonlinear finite element analysis combined piping loads...

... 10 02 2011 design engineering elasticity fasteners flanges gaskets Appendices 2 and Y ( 1 2 ) of the ASME code Sec. VIII cover flanges with a ring gasket located within the bolt circle and flanges with metal to metal contact outside the bolt circle, respectively. The first one...

.... creep design engineering fatigue nuclear power stations pipes thermal expansion thermal stresses 13 07 2007 16 12 2009 31 01 2011 31 01 2011 Several possibilities for a revision of the code have been discussed above but there is a better way. Rather than Eq. (10a...

... to the tube frequency. Damping is formulated in terms of tube and tube-support parameters. Semi-empirical formulations for damping of heat exchanger tubes in liquids are recommended for design purposes. 11 09 2008 06 10 2009 21 01 2011 21 01 2011 damping design engineering...

... and in the new ISO collapse model, H t assumed to be 0.22 and k y is shown in Table 1 . 18 06 2009 23 05 2010 20 01 2011 20 01 2011 design engineering metallurgical industries oil technology pipes safety standards The technical basis...

... geometry design engineering mechanical engineering computing mechanical stability mechanical strength shells (structures) standards shell structures advanced computational modeling elastic-plastic nonlinear analysis buckling collapse limit states imperfections bifurcation snap-through...

... design engineering elasticity finite element analysis mechanical stability mechanical strength plasticity shells (structures) The task of assessing the true strength of a shell structure has become much easier, following the development of a powerful nonlinear computer software...

... and a standard deviation equal to 1 ( 3 ). fatigue nuclear piping probabilistic design reliability design engineering fatigue pipes reliability 17 10 2009 22 08 2010 27 09 2010 27 09 2010 2010 American Society of Mechanical Engineers ...