In this paper, the performance augmentation of underactuated fingers through additional actuators is presented and discussed. Underactuated, also known as self-adaptive, fingers typically only rely on a single actuator for a given number of output degrees of freedom (DOF), generally equal to the number of phalanges. Therefore, once the finger is mechanically designed and built, little can be done using control algorithms to change the behavior of this finger, both during the closing motion and the grasp. We propose to use more than one actuator to drive underactuated fingers to improve the typical metrics used to measure their grasp performances (such as stiffness and stability). In order to quantify these improvements, two different scenarios are presented and discussed. The first one analyzes the impact of adding actuators along the transmission linkage of a classical architecture while the second focuses on a finger with a dual-drive actuation system for which both actuators are located inside the palm. A general kinetostatic analysis is first carried out and adapted to cover the case of underactuated fingers using more than one actuator. Typical performance indices are subsequently presented and optimizations are performed to compare the best designs achievable with respect to stiffness and grasp stability, depending on the number of actuators.
Skip Nav Destination
Article navigation
August 2017
Research-Article
Performance Augmentation of Underactuated Fingers' Grasps Using Multiple Drive Actuation
Jean-Michel Boucher,
Jean-Michel Boucher
Department of Mechanical Engineering,
Polytechnique Montreal,
Montreal, QC H3T 1J4, Canada
e-mail: jean-michel.boucher@polymtl.ca
Polytechnique Montreal,
Montreal, QC H3T 1J4, Canada
e-mail: jean-michel.boucher@polymtl.ca
Search for other works by this author on:
Lionel Birglen
Lionel Birglen
Department of Mechanical Engineering,
Polytechnique Montreal,
Montreal, QC H3T 1J4, Canada
e-mail: lionel.birglen@polymtl.ca
Polytechnique Montreal,
Montreal, QC H3T 1J4, Canada
e-mail: lionel.birglen@polymtl.ca
Search for other works by this author on:
Jean-Michel Boucher
Department of Mechanical Engineering,
Polytechnique Montreal,
Montreal, QC H3T 1J4, Canada
e-mail: jean-michel.boucher@polymtl.ca
Polytechnique Montreal,
Montreal, QC H3T 1J4, Canada
e-mail: jean-michel.boucher@polymtl.ca
Lionel Birglen
Department of Mechanical Engineering,
Polytechnique Montreal,
Montreal, QC H3T 1J4, Canada
e-mail: lionel.birglen@polymtl.ca
Polytechnique Montreal,
Montreal, QC H3T 1J4, Canada
e-mail: lionel.birglen@polymtl.ca
Manuscript received August 14, 2016; final manuscript received March 7, 2017; published online April 27, 2017. Assoc. Editor: Sarah Bergbreiter.
J. Mechanisms Robotics. Aug 2017, 9(4): 041003 (10 pages)
Published Online: April 27, 2017
Article history
Received:
August 14, 2016
Revised:
March 7, 2017
Citation
Boucher, J., and Birglen, L. (April 27, 2017). "Performance Augmentation of Underactuated Fingers' Grasps Using Multiple Drive Actuation." ASME. J. Mechanisms Robotics. August 2017; 9(4): 041003. https://doi.org/10.1115/1.4036220
Download citation file:
Get Email Alerts
Cited By
Design of Rolling Motion for Snake-like Robots using Center-of-Gravity (COG) Shift
J. Mechanisms Robotics
Modelling and Control of Cable Driven Exoskeleton for Arm Rehabilitation
J. Mechanisms Robotics
Design of an underactuated, flexure-based gripper, actuated through a push-pull flexure
J. Mechanisms Robotics
Related Articles
An Underactuated Robotic Arm Based on Differential Gears for Capturing Moving Targets: Analysis and Design
J. Mechanisms Robotics (August,2016)
A Linear Multiport Network Approach for Elastically Coupled Underactuated Grippers
J. Mechanisms Robotics (October,2017)
Application of a Biphasic Actuator in the Design of the CloPeMa Robot Gripper
J. Mechanisms Robotics (February,2015)
A New Seven Degrees-of-Freedom Parallel Robot With a Foldable Platform
J. Mechanisms Robotics (August,2018)
Related Proceedings Papers
Related Chapters
Backlash
Design and Application of the Worm Gear
GD&T as a Language
Geometric Dimensioning and Tolerancing Handbook: Applications, Analysis & Measurement
GD&T as a Language
Geometric Dimensioning and Tolerancing: Applications, Analysis, Gauging and Measurement [per ASME Y14.5-2018]