Dual-fuel (DF) engines offer great fuel flexibility since they can either run on gaseous or liquid fuels. In the case of diesel pilot-ignited DF engines, the main source of energy is provided by gaseous fuel, whereas the diesel fuel acts only as an ignition source. Therefore, a proper auto-ignition of the pilot fuel is of utmost importance for combustion in DF engines. However, auto-ignition of the pilot fuel suffers from lower compression temperatures of Miller or Atkinson valve timings. These valve timings are applied to increase efficiency and lower nitrogen oxide (NOx) engine emissions. In order to improve the ignition, it is necessary to understand which parameters influence the ignition in DF engines. For this purpose, experiments were conducted and the influence of parameters, such as injection pressure, pilot fuel quantity, compression temperature, and air–fuel (A/F) equivalence ratio of the homogenous natural gas–air mixture were investigated. The experiments were performed on a periodically chargeable combustion cell using optical high-speed recordings and thermodynamic measurement techniques for pressure and temperature. The study reveals that the quality of the diesel pilot ignition in terms of short ignition delay and a high number of ignited sprays significantly depends on the injection parameters and operating conditions. In most cases, the pilot fuel suffers from too high dilution due to its small quantity and long ignition delays. This results in a small number of ignited sprays and consequently leads to longer combustion durations. Furthermore, the experiments confirm that the natural gas of the background mixture influences the auto-ignition of the diesel pilot oil.
Skip Nav Destination
Article navigation
October 2018
Research-Article
Influence of Injection Parameters and Operating Conditions on Ignition and Combustion in Dual-Fuel Engines
Marcus Grochowina,
Marcus Grochowina
Institute of Thermodynamics,
Technical University of Munich,
Garching 85747, Germany
e-mail: Grochowina@td.mw.tum.de
Technical University of Munich,
Garching 85747, Germany
e-mail: Grochowina@td.mw.tum.de
Search for other works by this author on:
Michael Schiffner,
Michael Schiffner
Institute of Thermodynamics,
Technical University of Munich,
Garching 85747, Germany
Technical University of Munich,
Garching 85747, Germany
Search for other works by this author on:
Simon Tartsch,
Simon Tartsch
Institute of Thermodynamics,
Technical University of Munich,
Garching 85747, Germany
Technical University of Munich,
Garching 85747, Germany
Search for other works by this author on:
Thomas Sattelmayer
Thomas Sattelmayer
Institute of Thermodynamics,
Technical University of Munich,
Garching 85747, Germany
Technical University of Munich,
Garching 85747, Germany
Search for other works by this author on:
Marcus Grochowina
Institute of Thermodynamics,
Technical University of Munich,
Garching 85747, Germany
e-mail: Grochowina@td.mw.tum.de
Technical University of Munich,
Garching 85747, Germany
e-mail: Grochowina@td.mw.tum.de
Michael Schiffner
Institute of Thermodynamics,
Technical University of Munich,
Garching 85747, Germany
Technical University of Munich,
Garching 85747, Germany
Simon Tartsch
Institute of Thermodynamics,
Technical University of Munich,
Garching 85747, Germany
Technical University of Munich,
Garching 85747, Germany
Thomas Sattelmayer
Institute of Thermodynamics,
Technical University of Munich,
Garching 85747, Germany
Technical University of Munich,
Garching 85747, Germany
1Corresponding author.
Contributed by the IC Engine Division of ASME for publication in the JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received February 22, 2018; final manuscript received March 6, 2018; published online June 25, 2018. Editor: David Wisler.
J. Eng. Gas Turbines Power. Oct 2018, 140(10): 102809 (10 pages)
Published Online: June 25, 2018
Article history
Received:
February 22, 2018
Revised:
March 6, 2018
Citation
Grochowina, M., Schiffner, M., Tartsch, S., and Sattelmayer, T. (June 25, 2018). "Influence of Injection Parameters and Operating Conditions on Ignition and Combustion in Dual-Fuel Engines." ASME. J. Eng. Gas Turbines Power. October 2018; 140(10): 102809. https://doi.org/10.1115/1.4040089
Download citation file:
Get Email Alerts
Shape Optimization of an Industrial Aeroengine Combustor to reduce Thermoacoustic Instability
J. Eng. Gas Turbines Power
Dynamic Response of A Pivot-Mounted Squeeze Film Damper: Measurements and Predictions
J. Eng. Gas Turbines Power
Review of The Impact Of Hydrogen-Containing Fuels On Gas Turbine Hot-Section Materials
J. Eng. Gas Turbines Power
Effects of Lattice Orientation Angle On Tpms-Based Transpiration Cooling
J. Eng. Gas Turbines Power
Related Articles
A Multicomponent Blend as a Diesel Fuel Surrogate for Compression Ignition Engine Applications
J. Eng. Gas Turbines Power (November,2015)
Autoignition of Hydrogen and Air Inside a Continuous Flow Reactor With Application to Lean Premixed Combustion
J. Eng. Gas Turbines Power (September,2008)
Errata: “Schlieren Observation of Spark-Ignited Premixed Charge Combustion Phenomena Using a Transparent Collimating Cylinder Engine” [ASME J. Eng. Gas Turbines Power, 2003, 125 , pp. 336–343]
J. Eng. Gas Turbines Power (April,2003)
Numerical Investigation of the Effect of Knock on Heat Transfer in a Turbocharged Spark Ignition Engine
J. Eng. Gas Turbines Power (December,2015)
Related Proceedings Papers
Related Chapters
Physiology of Human Power Generation
Design of Human Powered Vehicles
Outlook
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Lay-Up and Start-Up Practices
Consensus on Operating Practices for Control of Water and Steam Chemistry in Combined Cycle and Cogeneration