A computational tool, called a Unified Integral Method (UIM) is reviewed. The method is used for preliminary design and performance analysis of simple diffusers with thin inlet boundary layers and subsonic flow in their inviscid core regions. The assumptions needed for application of a UIM are not very restrictive in many practical cases: straight diffusers with thin, turbulent inlet boundary layers and subsonic, irrotational core flows. The method provides designers with useful results including pressure recovery, location of separation and stalled regions, and exit plane profiles which may be used to evaluate total pressure loss and various flow distortion indices. Besides reviewing some basic concepts concerning stall and separation, describing the basis of the method and some details for making the UIM work, actual cases where it was tested versus data are discussed. In addition, UIM results are compared to results obtained by a RANS method run in a well known duct flow solver for a subsonic diffuser where data are also available. In another case, its output and data were compared to results from a CFD code typical of the many design codes in use in industry today. In both cases, the UIM results were as good, or better than those from the higher level methods, and the UIM is much simpler and easier to use as a design tool.

Issue Section:
Research Papers
Topics:
Design, Diffusers, Flow (Dynamics), Boundary layers, Pressure, Separation (Technology), Computational fluid dynamics, Ducts, Reynolds-averaged Navier–Stokes equations, Subsonic flow, Turbulence
1.
Ashjaee, J., 1980, “Subsonic Turbulent Flow in Plane-Wall Diffusers; Pressure Recovery and Transitory Stall,” Ph.D. dissertation, Dept. of Mechanical Engineering, Stanford University.
2.
Ashjaee
 
J.
, and
Johnston
 
J. P.
,
1980
, “
Subsonic Turbulent Flow in Plane Wall Diffusers: Peak Pressure Recovery and Transitory Stall
,”
ASME JOURNAL OF FLUIDS ENGINEERING
, Vol.
102
, pp.
275
–
282
.
3.
Bardina
 
J. G.
,
Lyrio
 
A.
,
Kline
 
S. J.
,
Ferziger
 
J.
, and
Johnston
 
J. P.
,
1981
, “
A Prediction Method for Planar Diffuser Flows
,”
ASME JOURNAL OF FLUIDS ENGINEERING
, Vol.
103
, 1981, pp.
315
–
321
.
4.
Bradshaw
 
P.
,
Ferris
 
D. H.
, and
Atwell
 
N. P.
,
1964
, “
Calculation of the Turbulent Boundary Layer Using the Turbulent Energy Equation
,”
Journal of Fluid Mechanics
, Vol.
9
, Part 4, pp.
591
–
625
.
5.
Childs, R. E., 1981, “A Computational Method for Subsonic Compressible Flow in Diffusers,” Ph.D. dissertation, Dept. of Mechanical Engineering, Stanford University, Stanford, CA.
6.
Childs, R. E., and Ferziger, J. H., 1983, “A Computational Method for Subsonic Compressible Flow in Diffusers,” Paper 83-0505, AIAA 21st Aerospace Sciences Meeting, Reno, NV, Jan. 10–13, 1983.
7.
Eaton, J. K., Westphal, R. V., and Johnston, J. P., 1981, “Two New Instruments for Flow Direction and Skin Friction Measurements in Separated Flow,” Flow its Measurement and Control in Science and Industry, Vol. 2, W. W. Durgin, ed., Instrument Society of America, ISBN 0-87664.511-2, pp. 77–90.
8.
Fraser
 
J. P.
,
1958
, “
Study of an Incompressible Turbulent Boundary Layer in a Conical Diffuser
,”
Proceedings ASCE, Journal of Hydraulic Division
, Vol.
84
, p.
1684
1684
.
9.
Ghose
 
S.
, and
Kline
 
S. J.
,
1978
, “
The Computation of Optimum Pressure Recovery in Two-Dimensional Diffusers
,”
ASME JOURNAL OF FLUIDS ENGINEERING
, Vol.
100
, pp.
419
–
426
.
10.
Kline
 
S. J.
,
Bardina
 
J. G.
, and
Strawn
 
R. C.
,
1983
, “
Correlation of the Detachment of Two-Dimensional Turbulent Boundary Layers
,”
AIAA Journal
, Vol.
21
, No.
1
, pp.
68
–
73
.
11.
Kline, S. J., Cantwell, B. J., and Lilley, G. M., 1982. Proceedings of the 1980–81 AFOSR-HTTM-Stanford Conference on Complex Turbulent Flows, Vols. I, II, and III, Dept. of Mechanical Engineering, Stanford University, Stanford, CA.
12.
Kuhn, G. D. and Nielsen, J. N., 1971, “An Analytic Method for Calculating Turbulent Separated Flows Due to Adverse Pressure Gradients,” Report No: TR NEAR-1-PU, Project Squid, U. S Office of Naval Research.
13.
Lyrio, A. A., 1981, “An Integral Method for the Computation of Steady and Unsteady Turbulent Boundary Layer Flows, Including the Transitory Stall Regime in Diffusers,” Ph.D. dissertation, Dept. of Mechanical Engineering, Stanford University.
14.
Mayer, D. W., and Kneeling, W., 1992, “Evaluation of Two Flow Analyses for Subsonic Diffuser Design,” AIAA Paper 92-0273, 30th Aerospace Sciences Meeting, Reno, NV, Jan. 6-9.
15.
Paynter, G., (1997), private communication.
16.
Rothe, P. H., Barry, J. J., Johnston, J. P., and Pulliam, T., 1997, “CFD Assessment With Diffuser Data,” Paper: FEDSM-3026, ASME Fluids Engineering Division Summer Meeting, June 22-26.
17.
Sajben
 
M.
and
Liao
 
Y.
,
1995
, “
Criterion for the Detachment of Laminar and Turbulent Boundary Layers
,”
AIAA Journal
, Vol.
33
, No.
11
, pp.
2114
–
2119
.
18.
Sajben, M. C., Kroutil, J. C., and Chen, C. P., 1977, “A High Speed Schlieren Investigation of High Speed Diffuser Flows with Dynamic Distortion,” Paper MDRL-77-17, McDonnell-Douglas Research Laboratory, St. Louis, MO, 1977.
19.
Sandborn
 
V. A.
, and
Kline
 
S. J.
,
1961
, “
Flow Models in Boundary Layer Stall Inception
,”
ASME Journal of Basic Engineering
, Vol.
83
, pp.
317
–
327
.
20.
Shimomura, I., and Ferziger, J. H., 1983, “A Program for Prediction of Diffuser Performance in the Unstalled and Stalled Flow Regimes,” Report PD-28, Thermosciences Div., Dept. of Mechanical Engineering, Stanford University.
21.
Simpson
 
R. L.
,
1981
, “
Review of Turbulent Flow Separation
,”
ASME JOURNAL OF FLUIDS ENGINEERING
, Vol.
103
, pp.
520
–
581
.
22.
Sovran, G., and Klomp, E. D., 1967, “Experimentally Determined Optimum Geometries for Rectilinear Diffusers with Rectangular, Conical, or Annular Cross-Section,” Fluid Mechanics of Internal Flow, G. Sovran, ed., Elsevier Publishing Co., New York, pp. 270–319.
23.
Yamazato, E. and Irabu, K., 1987, “A Prediction for Two-Dimensional Diffuser Flows,” Bulletin Faculty of Engineering, University of the Ryukyus, Japan, No. 34.
This content is only available via PDF.
Copyright © 1998
 by The American Society of Mechanical Engineers
You do not currently have access to this content.