An analytical model is derived for the calculation of thermo-mechanical induced stresses in area array flip chip assemblies. This analytical model is based on structural mechanics and has the ability to characterize the nature and to estimate the magnitude of the induced stresses. The extension of this model compared to existing procedures is its applicability to area array systems, which behave significantly different from peripheral assemblies. The model is compared to finite element simulations. The model calculates accurately the forces and bending moments acting on the flip chip connections. The transformation of these forces and moments into stresses is less accurate as the model does not include stress concentrations near the corners. The model simulates very well the different parameter trends such as chip size and is therefore well suited for understanding parameter sensitivity studies.

1.
The Nordic Electronics Packaging Guideline, http://extra.ivf.se/ngl
2.
Vandevelde, B., Beyne, E., Vandepitte, D., and Baelmans, M., 2002, “Semi-Analytical Model for Calculation of Induced Strains in Solder Joints of Underfilled Flip Chip Assemblies,” Proceedings of the 3rd Eurosime conference, pp. 86–91, Paris, France, April 14–17.
3.
Vandevelde
,
B.
,
Christiaens
,
F.
,
Beyne
,
E.
,
Peeters
,
J.
,
Allaert
,
K.
,
Vandepitte
,
D.
, and
Berghmans
,
J.
,
1998
, “
A Thermo-Mechanical Model for Leadless Solder Interconnections in Flip Chip Assemblies
,”
IEEE Trans. Compon., Packag. Manuf. Technol., Part A
,
21
, pp.
177
185
.
4.
Suhir, E., 1988, “Thermal Stress Failures in Microelectronic Components—Review and Extension,” Advances in Thermal modelling of Electronic Components and Systems, A. Bar-Cohen and A. D. Kraus, eds., New York, Hemisphere, Vol. 1, Ch. 5, pp. 337–412.
5.
Tummala, R. R., and Rymaszewski, E. S., 1989, Microelectronics Packaging Handbook, Van Nostrand Reinhold, New York.
6.
Jeanotte, D., Goldmann, L., and Howard, R., 1989, Package Reliability, Micro-electronics Handbook, R. Tummala and E. Rymaszewski, eds., New York, Van Nostrand Reinhold, Ch. 5, pp. 295–299.
7.
Robert
,
M.
, and
Keer
,
L. M.
,
1987
, “
An Elastic Cylinder With Prescribed Displacements at the Ends—Asymmetric Case
,”
Quart. Journal on Applied Mathematics
,
40
, pp.
365
381
.
8.
Hall
,
P. M.
,
1984
, “
Forces, Moments and Displacements During Thermal Chamber Cycling of Leadless Ceramic Chip Carriers Soldered to Printed Circuit Boards
,”
IEEE Trans. Compon., Hybrids, Manuf. Technol.
,
CHMT-7
, pp.
314
327
, Dec.
9.
Chen
,
W. T.
, and
Nelson
,
C. W.
,
1979
, “
Thermal Stress in Bonded Joints
,”
IBM J. Res. Dev.
,
23
(
2
), pp.
179
188
, March.
10.
Lau
,
J. H.
,
Rice
,
D. W.
, and
Avery
,
P. A.
,
1987
, “
Elasto-Plastic Analysis of Surface Mount Solder Joints
,”
IEEE Trans. Compon., Hybrids, Manuf. Technol.
,
CHMT-10
, pp.
346
357
.
11.
Engelmaier
,
W.
,
1983
, “
Fatigue of Leadless Chip Carrier Solder Joints During Power Cycling
,”
IEEE Trans. Compon., Hybrids, Manuf. Technol.
,
CHMT-6
, pp.
232
237
.
12.
Vandevelde, B., and Beyne, E., 1998, “Thermo-Mechanical Analysis for Optimizing the Underfill Material Properties of Flip Chip Assemblies,” SEM Spring Conference on Experimental/Numerical Mechanics in Electronic Packaging, Houston, USA, June 1–3.
13.
Vandevelde, B., 2002, “Thermo-Mechanical Modelling of Solder Joint Reliability for Electronic Package Systems,” PhD thesis, Catholic University of Leuven; March.
You do not currently have access to this content.