Hip resurfacing is an alternative to total hip arthroplasty in which the femoral head surface is replaced with a metallic shell, thus preserving most of the proximal femoral bone stock. Accidental notching of the femoral neck during the procedure may predispose it to fracture. We examined the effect of neck notching on the strength of the proximal femur. Six composite femurs were prepared without a superior femoral neck notch, six were prepared in an inferiorly translated position to create a 2 mm notch, and six were prepared with a 5 mm notch. Six intact synthetic femurs were also tested. The samples were loaded to failure axially. A finite element model of a composite femur with increasing superior notch depths computed maximum equivalent stress and strain distributions. Experimental results showed that resurfaced synthetic femurs were significantly weaker than intact femurs (mean failure of 7034 N, ). The 2 mm notched group (mean failure of 4034 N) was significantly weaker than the un-notched group (mean failure of 5302 N, ). The 5 mm notched group (mean failure of 2808 N) was also significantly weaker than both the un-notched and the 2 mm notched groups (, , respectively). The finite element model showed the maximum equivalent strain in the superior reamed cancellous bone increasing with corresponding notch size. Fracture patterns inferred from equivalent stress distributions were consistent with those obtained from mechanical testing. A superior notch of 2 mm weakened the proximal femur by 24%, and a 5 mm notch weakened it by 47%. The finite element analysis substantiates this showing increasing stress and strain distributions within the prepared femoral neck with increasing notch depth.
Skip Nav Destination
e-mail: zderor@smh.toronto.on.ca
Article navigation
April 2009
Research Papers
A Biomechanical and Finite Element Analysis of Femoral Neck Notching During Hip Resurfacing
Edward T. Davis,
Edward T. Davis
Fellow of the Royal College of Surgeons
Royal Orthopaedic NHS Foundation Trust
, Birmingham B31-2AP, UK
Search for other works by this author on:
Michael Olsen,
Michael Olsen
Martin Orthopaedic Biomechanics Laboratory,
St. Michael's Hospital
, Toronto, ON, M5B-1W8, Canada
Search for other works by this author on:
Rad Zdero,
Rad Zdero
Martin Orthopaedic Biomechanics Laboratory,
e-mail: zderor@smh.toronto.on.ca
St. Michael's Hospital
, Toronto, ON, M5B-1W8, Canada
Search for other works by this author on:
Marcello Papini,
Marcello Papini
Department of Mechanical and Industrial Engineering,
Ryerson University
, Toronto, ON, M5B-2K3, Canada
Search for other works by this author on:
James P. Waddell,
James P. Waddell
Fellow of the Royal College of Surgeons (Canada)
Department of Surgery, Division of Orthopaedics,
St. Michael's Hospital
, Toronto, ON, M5B-1W8, Canada
Search for other works by this author on:
Emil H. Schemitsch
Emil H. Schemitsch
Fellow of the Royal College of Surgeons (Canada)
Martin Orthopaedic Biomechanics Laboratory,
St. Michael's Hospital
, Toronto, ON, M5B-1W8, Canada; Department of Surgery, Division of Orthopaedics, St. Michael's Hospital
, Toronto, ON, M5B-1W8, Canada
Search for other works by this author on:
Edward T. Davis
Fellow of the Royal College of Surgeons
Royal Orthopaedic NHS Foundation Trust
, Birmingham B31-2AP, UK
Michael Olsen
Martin Orthopaedic Biomechanics Laboratory,
St. Michael's Hospital
, Toronto, ON, M5B-1W8, Canada
Rad Zdero
Martin Orthopaedic Biomechanics Laboratory,
St. Michael's Hospital
, Toronto, ON, M5B-1W8, Canadae-mail: zderor@smh.toronto.on.ca
Marcello Papini
Department of Mechanical and Industrial Engineering,
Ryerson University
, Toronto, ON, M5B-2K3, Canada
James P. Waddell
Fellow of the Royal College of Surgeons (Canada)
Department of Surgery, Division of Orthopaedics,
St. Michael's Hospital
, Toronto, ON, M5B-1W8, Canada
Emil H. Schemitsch
Fellow of the Royal College of Surgeons (Canada)
Martin Orthopaedic Biomechanics Laboratory,
St. Michael's Hospital
, Toronto, ON, M5B-1W8, Canada; Department of Surgery, Division of Orthopaedics, St. Michael's Hospital
, Toronto, ON, M5B-1W8, CanadaJ Biomech Eng. Apr 2009, 131(4): 041002 (8 pages)
Published Online: January 30, 2009
Article history
Received:
November 19, 2007
Revised:
August 7, 2008
Published:
January 30, 2009
Citation
Davis, E. T., Olsen, M., Zdero, R., Papini, M., Waddell, J. P., and Schemitsch, E. H. (January 30, 2009). "A Biomechanical and Finite Element Analysis of Femoral Neck Notching During Hip Resurfacing." ASME. J Biomech Eng. April 2009; 131(4): 041002. https://doi.org/10.1115/1.3072889
Download citation file:
Get Email Alerts
Effect of Collagen Fiber Tortuosity Distribution on the Mechanical Response of Arterial Tissues
J Biomech Eng (February 2025)
Related Articles
Simulating Distal Radius Fracture Strength Using Biomechanical Tests: A Modeling Study Examining the Influence of Boundary Conditions
J Biomech Eng (November,2011)
The Biomechanical Consequence of Insufficient Femoral Component Lateralization and Exposed Cancellous Bone in Hip Resurfacing Arthroplasty
J Biomech Eng (August,2010)
Related Proceedings Papers
Related Chapters
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design
In Situ Observations of the Failure Mechanisms of Hydrided Zircaloy-4
Zirconium in the Nuclear Industry: 20th International Symposium
Novel and Efficient Mathematical and Computational Methods for the Analysis and Architecting of Ultralight Cellular Materials and their Macrostructural Responses
Advances in Computers and Information in Engineering Research, Volume 2